Quest Diagnostics specimen packaging & transport guide

Quest Diagnostics publishes minimum packaging guidelines for specimens submitted to its laboratories. The points below summarize that public documentation; always check the current Quest page and the test directory entry for the specific test. Package each specimen in a labeled primary receptacle, a leak-proof secondary bag with absorbent, and a rigid outer container, with the requisition kept separate.

Independent guide · Not affiliated with Quest Diagnostics · Updated 2026-10-31

What Quest Diagnostics's public documentation says

  • Quest's specimen transport bag has two pouches: specimen containers go in the front pocket and the requisition goes in the rear pocket with the barcode visible in the bottom corner of the bag. (source)
  • The top copy of the requisition is folded in half widthwise with the patient name and barcode facing out; the bag is sealed without obstructing the bag's barcode. (source)
  • Specimens are kept separated by temperature: room temperature, refrigerated and frozen. (source)
  • Frozen specimens should be transported in plastic screw-cap containers only, in a separate specimen bag with a separate test requisition. (source)
  • When packaging with dry ice, the dry ice cannot be contained in a sealed container or bag; gases must be allowed to vent. (source)
  • For specimens classified as infectious substances, Quest states that air transport requires a sealed 95 kPa bag, while the 95 kPa component is not required for ground transport, and asks clients to inform Quest before or at pickup. (source)
  • Manual requisitions are packaged one patient per specimen bag; irreplaceable specimens go in a purple "Irreplaceable Specimen" bag with the specimen in the front pocket and requisition in the rear pocket. (source)

Lab instructions change. Check the linked pages and the specific test's directory entry before you package.

Official Quest Diagnostics resources

Diagram of triple packaging for lab specimens: leak-proof primary tube, secondary biohazard bag with absorbent pad, rigid outer box marked UN3373
Triple packaging: primary receptacle, leak-proof secondary bag with absorbent, and rigid outer packaging.

General packaging steps

  1. Primary receptacle. Use the container the test requires, check the expiration date, tighten caps fully, and label with at least two patient identifiers plus collection date and time.
  2. Requisition. Match the order to the label exactly and place it in the bag's separate rear pocket so it stays dry.
  3. Secondary bag. Seal specimens in a leak-proof biohazard bag with enough absorbent for all the liquid; keep fragile tubes from touching.
  4. Temperature. One temperature per bag; follow the lab's ranges for ambient, refrigerated and frozen.
  5. Outer container. Use a rigid, insulated container; mark UN3373 for Category B shipments and follow dry-ice rules when used.
  6. Handoff. Count bags with the courier, note the time and temperatures, and keep your copy of the manifest.
Two-pocket specimen transport bag with tubes in the sealed front pouch and folded test requisition in the rear pocket with barcode showing
Step 2: specimens in the sealed front pouch, requisition folded in the rear pocket so paperwork stays dry.
Three specimen bags separated by temperature: ambient room temperature, refrigerated and frozen
Step 5: never mix temperatures in one bag. Each lab publishes its own temperature ranges.

If your practice is in the Phoenix metro or the Austin area and you send specimens to a national lab's local patient service center, processing site or drop location, a local courier can carry the packaged specimens across town on your schedule. Package exactly as the lab instructs — the courier does not repackage specimens.

Courier pickup checklist for lab specimens: caps tight, requisition in rear pocket, one patient per bag, temperatures separated
Step 10: a quick pickup checklist before the specimen leaves your office.

For the full walkthrough — including dry ice, 95 kPa bags, UN3373 vs. Category A, chain of custody and stability — read our complete specimen packaging and transport guide, and see the CDC, DOT, IATA and OSHA resources.

Frequently asked questions

How do I package a specimen for Quest Diagnostics?
Start with Quest Diagnostics's own published instructions, summarized with sources on this page, and its test directory for test-specific rules. As general guidance (not Quest Diagnostics-specific), most labs also expect a tightly capped, labeled primary receptacle, a leak-proof bag with absorbent, the requisition kept separate from the specimen, and temperatures separated.
Is Progressive Couriers affiliated with Quest Diagnostics?
No. Progressive Couriers is an independent courier and is not affiliated with, endorsed by, or an approved courier for Quest Diagnostics. This guide is informational.
Where does Progressive Couriers deliver specimens?
In the Phoenix metro and Arizona, and in the Austin, TX area. We transport ordinary clinical specimens, including Category B and exempt specimens, and do not accept Category A infectious substances.

Lab specimen transport requirements: packaging, temperature & chain of custody →

OSHA bloodborne pathogens & specimen transport requirements →

Not medical, legal or regulatory advice. This guide is general information last reviewed 2026-10-31. Requirements change; always follow the receiving laboratory's current test directory and instructions, and current DOT, IATA and OSHA rules. Illustrations are original diagrams for general education.

Questions? 602-499-2672